• <th id="je1vv"></th>
      <form id="je1vv"><strike id="je1vv"></strike></form>

      網站導航

      常見問題

      當前位置:主頁 > 常見問題 >

      萬能銑床的銑刀如何修磨

      時間:2020-08-26 21:54 點擊次數:

      萬能銑床的銑刀的常用4種銑刀類型,以其中的一種類型說說銑刀的修磨方法:

      萬能銑床銑刀的常見類型,分為四種,分別為:面銑刀、力銑刀、三面刃銑刀、螺紋銑刀等,銑刀在各個銑床中的作用是非常大的,它就像一把利刃,能將一個個的待加工的產品完美雕琢。

      萬能銑床立銑刀端刃修磨方法:

      把原刀架工作臺換成立銑刀刃磨附件的工作臺。將R8彈性套筒刺進銑刀附件工作臺的錐形孔中,將直徑尺度巨細適宜的立銑刀刺進R8套筒并將它固定,因而螺旋立銑刀將不再滾動。將立銑刀刀具調整到高于砂輪的基地。

      按萬能銑床銑刀側刃后角的度數滾動0-40度的刀架工作臺,使立銑刀的附件工作臺調整出適宜的刃磨視點。用螺旋立銑刀刃磨附件上的導向可調支架固定槽針去貼緊立銑刀側刃螺旋溝槽進行導向引導,然后直接早年到后自在旋轉(靠導向引導)推進手把有些的前后抽動磨削辦法刃磨銑刀后角的螺旋刃口。當主后角磨完后就磨副后角,將導向可調支架固定槽針刺進第二傾斜度的螺旋槽中,然后象磨榜首傾斜度相同去磨。

      掌握銑刀的研磨方法,對于萬能銑床的使用能起到事半功倍的效果,可以提高銑床的加工生產效率,更好的為生產服務。

       

       

      There are four types of milling cutter commonly used in universal milling machine. One of them is about the grinding method of milling cutter

      The common types of universal milling cutter are divided into four types: face milling cutter, force milling cutter, three side edge milling cutter, thread milling cutter, etc. the function of milling cutter in each milling machine is very big. It is like a sharp edge, which can perfectly carve the products to be processed one by one.

      End milling cutter end grinding method of universal milling machine:

      Replace the original turret table with the one for milling cutter grinding accessories. The R8 elastic sleeve is inserted into the conical hole of the milling cutter accessory table, and the end milling cutter with suitable diameter and size is inserted into the R8 sleeve and fixed, so the spiral end mill will not roll any more. Adjust the end mill tool to a base higher than the grinding wheel.

      According to the degree of the back angle of the milling cutter side edge of the universal milling machine, roll the tool rest table of 0-40 degrees to adjust the appropriate grinding point of the end mill's accessory table. The screw end mill is used to grind the guide adjustable bracket fixed slot needle on the accessory to close to the spiral groove of the end mill side edge for guiding and guiding, and then the screw edge of the back corner of the milling cutter is grinded by the forward and backward twitch grinding method of pushing the handlebar freely from the early years to the back. After grinding the main rear angle, grind the rear angle of the pair, needle the fixed groove of the guide adjustable bracket into the spiral groove with the second inclination, and then grind it with the same inclination as the top of the grinding table.

      Master the milling cutter grinding method, for the use of universal milling machine can play a multiplier effect, can improve the milling machine processing production efficiency, better service for production.

      ?


      大家都在看的產品

      電話:13280489678

      QQ:675609587

      郵箱:675609587@qq.com

      聯系人:鄭經理

      地址:山東省棗莊市滕州市經濟開發區

      Copyright © 山東沈北數控機床有限公司 版權所有 備案號:魯ICP備20014639號-1

      在線客服 聯系方式 二維碼

      服務熱線

      13280489678

      掃一掃,關注我們

      KTV多人游戏